Wifi Problems

allen286 · May 10, 2015

Hey everyone,

I am very close on my installation. I built my kernel using genkernel. All the necessary drivers are, as far as I can tell, loading appropriately. I am typing this from my Ubuntu install, however, because I have no internet in Funtoo. The driver modules for both the ethernet and wifi are loading and I am even able to scan for wireless networks; however, I cannot connect to any networks. Any ideas? Let me know if you need any output.

thanks in advance!

-Hunter A.

666threesixes666 · May 11, 2015

did you emerge sys-kernel/linux-firmware?

post dmesg of the funtoo install

post lspci -k

post lsusb instead if its a usb device.

are you using network manager? post which method you're using to connect to wifi.

uhhh to post the dmesg & lspci copy them to files then access the files when you chroot to emerge linux-firmware or what ever, you could access them just by mounting the funtoo drive on your live distro

allen286 · May 11, 2015

Thanks for the reply! I did install linux-firmware, and I am using network manager from Gnome 3.

Here's lspci -k:

00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
	Subsystem: CLEVO/KAPOK Computer Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06)
	Kernel driver in use: pcieport
00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05)
	Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family USB xHCI
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci
00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
	Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family MEI Controller
00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05)
	Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family USB EHCI
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci
00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
	Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset High Definition Audio Controller
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5)
	Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5)
	Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 (rev d5)
	Kernel driver in use: pcieport
00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d5)
	Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05)
	Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family USB EHCI
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci
00:1f.0 ISA bridge: Intel Corporation HM87 Express LPC Controller (rev 05)
	Subsystem: CLEVO/KAPOK Computer HM87 Express LPC Controller
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05)
	Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode]
	Kernel driver in use: ahci
	Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
	Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family SMBus Controller
	Kernel modules: i2c_i801
01:00.0 VGA compatible controller: NVIDIA Corporation GK104M [GeForce GTX 860M] (rev a1)
	Subsystem: CLEVO/KAPOK Computer GK104M [GeForce GTX 860M]
	Kernel driver in use: nvidia
	Kernel modules: nvidia
01:00.1 Audio device: NVIDIA Corporation GK104 HDMI Audio Controller (rev a1)
	Subsystem: CLEVO/KAPOK Computer GK104 HDMI Audio Controller
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel
03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5289 (rev 01)
	Subsystem: CLEVO/KAPOK Computer Device 0376
03:00.2 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0a)
	Subsystem: CLEVO/KAPOK Computer RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
	Kernel driver in use: r8169
	Kernel modules: r8169
04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83)
	Subsystem: Intel Corporation Dual Band Wireless-AC 3160
	Kernel driver in use: iwlwifi
	Kernel modules: iwlwifi

Here's the dmesg output:

[    0.336395] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.336563] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug PME]
[    0.336717] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
[    0.337080] PCI host bridge to bus 0000:00
[    0.337143] pci_bus 0000:00: root bus resource [bus 00-7e]
[    0.337208] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.337272] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.337337] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.337404] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[    0.337469] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[    0.337536] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[    0.337601] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[    0.337668] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[    0.337733] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[    0.337798] pci_bus 0000:00: root bus resource [mem 0x90000000-0xfeafffff]
[    0.337869] pci 0000:00:00.0: [8086:0c04] type 00 class 0x060000
[    0.337940] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
[    0.337970] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.338006] pci 0000:00:01.0: System wakeup disabled by ACPI
[    0.338127] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[    0.338144] pci 0000:00:14.0: reg 0x10: [mem 0xec300000-0xec30ffff 64bit]
[    0.338200] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.338226] pci 0000:00:14.0: System wakeup disabled by ACPI
[    0.338325] pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
[    0.338342] pci 0000:00:16.0: reg 0x10: [mem 0xec31a000-0xec31a00f 64bit]
[    0.338400] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.338467] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[    0.338485] pci 0000:00:1a.0: reg 0x10: [mem 0xec318000-0xec3183ff]
[    0.338567] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.338604] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.338705] pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
[    0.338719] pci 0000:00:1b.0: reg 0x10: [mem 0xec310000-0xec313fff 64bit]
[    0.338782] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.338809] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.338905] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
[    0.338968] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.338997] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.339093] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400
[    0.339155] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.339184] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    0.339280] pci 0000:00:1c.3: [8086:8c16] type 01 class 0x060400
[    0.339342] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.339371] pci 0000:00:1c.3: System wakeup disabled by ACPI
[    0.339468] pci 0000:00:1c.4: [8086:8c18] type 01 class 0x060400
[    0.339538] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.339568] pci 0000:00:1c.4: System wakeup disabled by ACPI
[    0.339670] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[    0.339688] pci 0000:00:1d.0: reg 0x10: [mem 0xec317000-0xec3173ff]
[    0.339770] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.339808] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.339908] pci 0000:00:1f.0: [8086:8c4b] type 00 class 0x060100
[    0.340054] pci 0000:00:1f.2: [8086:8c03] type 00 class 0x010601
[    0.340067] pci 0000:00:1f.2: reg 0x10: [io  0xf070-0xf077]
[    0.340074] pci 0000:00:1f.2: reg 0x14: [io  0xf060-0xf063]
[    0.340079] pci 0000:00:1f.2: reg 0x18: [io  0xf050-0xf057]
[    0.340085] pci 0000:00:1f.2: reg 0x1c: [io  0xf040-0xf043]
[    0.340091] pci 0000:00:1f.2: reg 0x20: [io  0xf020-0xf03f]
[    0.340098] pci 0000:00:1f.2: reg 0x24: [mem 0xec316000-0xec3167ff]
[    0.340131] pci 0000:00:1f.2: PME# supported from D3hot
[    0.340186] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[    0.340198] pci 0000:00:1f.3: reg 0x10: [mem 0xec315000-0xec3150ff 64bit]
[    0.340216] pci 0000:00:1f.3: reg 0x20: [io  0xf000-0xf01f]
[    0.340311] pci 0000:01:00.0: [10de:119a] type 00 class 0x030000
[    0.340321] pci 0000:01:00.0: reg 0x10: [mem 0xeb000000-0xebffffff]
[    0.340331] pci 0000:01:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.340340] pci 0000:01:00.0: reg 0x1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[    0.340347] pci 0000:01:00.0: reg 0x24: [io  0xe000-0xe07f]
[    0.340353] pci 0000:01:00.0: reg 0x30: [mem 0xec000000-0xec07ffff pref]
[    0.340407] pci 0000:01:00.0: System wakeup disabled by ACPI
[    0.340506] pci 0000:01:00.1: [10de:0e0a] type 00 class 0x040300
[    0.340516] pci 0000:01:00.1: reg 0x10: [mem 0xec080000-0xec083fff]
[    0.356848] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.356912] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.356914] pci 0000:00:01.0:   bridge window [mem 0xeb000000-0xec0fffff]
[    0.356917] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.356962] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.357089] pci 0000:03:00.0: [10ec:5289] type 00 class 0xff0000
[    0.357107] pci 0000:03:00.0: reg 0x10: [mem 0xec200000-0xec20ffff]
[    0.357245] pci 0000:03:00.0: supports D1 D2
[    0.357246] pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.357273] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.357382] pci 0000:03:00.2: [10ec:8168] type 00 class 0x020000
[    0.357400] pci 0000:03:00.2: reg 0x10: [io  0xd000-0xd0ff]
[    0.357426] pci 0000:03:00.2: reg 0x18: [mem 0xd2104000-0xd2104fff 64bit pref]
[    0.357443] pci 0000:03:00.2: reg 0x20: [mem 0xd2100000-0xd2103fff 64bit pref]
[    0.357524] pci 0000:03:00.2: supports D1 D2
[    0.357525] pci 0000:03:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.357550] pci 0000:03:00.2: System wakeup disabled by ACPI
[    0.376883] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.376948] pci 0000:00:1c.2:   bridge window [io  0xd000-0xdfff]
[    0.376950] pci 0000:00:1c.2:   bridge window [mem 0xec200000-0xec2fffff]
[    0.376954] pci 0000:00:1c.2:   bridge window [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.377024] pci 0000:04:00.0: [8086:08b3] type 00 class 0x028000
[    0.377061] pci 0000:04:00.0: reg 0x10: [mem 0xec100000-0xec101fff 64bit]
[    0.377248] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[    0.377277] pci 0000:04:00.0: System wakeup disabled by ACPI
[    0.396915] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.396980] pci 0000:00:1c.3:   bridge window [mem 0xec100000-0xec1fffff]
[    0.397031] pci 0000:00:1c.4: PCI bridge to [bus 05-3d]
[    0.397097] pci 0000:00:1c.4:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.397102] pci 0000:00:1c.4:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.397132] pci_bus 0000:00: on NUMA node 0
[    0.397133] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
[    0.397723] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.398317] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.398908] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 10 11 12 14 15)
[    0.399500] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 10 11 12 14 15)
[    0.400090] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.400774] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.401458] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 10 11 12 14 15)
[    0.402047] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.402815] ACPI: Enabled 5 GPEs in block 00 to 3F
[    0.402996] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.403119] vgaarb: setting as boot device: PCI:0000:01:00.0
[    0.403183] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.403250] vgaarb: loaded
[    0.403309] vgaarb: bridge control possible 0000:01:00.0
[    0.403425] SCSI subsystem initialized
[    0.403550] PCI: Using ACPI for IRQ routing
[    0.406428] PCI: pci_cache_line_size set to 64 bytes
[    0.406477] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[    0.406478] e820: reserve RAM buffer [mem 0x7d21f000-0x7fffffff]
[    0.406479] e820: reserve RAM buffer [mem 0x7d981000-0x7fffffff]
[    0.406480] e820: reserve RAM buffer [mem 0x8dc0b000-0x8fffffff]
[    0.406481] e820: reserve RAM buffer [mem 0x8e676000-0x8fffffff]
[    0.406482] e820: reserve RAM buffer [mem 0x8f000000-0x8fffffff]
[    0.406483] e820: reserve RAM buffer [mem 0x46f000000-0x46fffffff]
[    0.406620] Switched to clocksource hpet
[    0.406765] pnp: PnP ACPI init
[    0.406882] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.406962] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.407099] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.407165] system 00:01: [io  0xffff] has been reserved
[    0.407228] system 00:01: [io  0xffff] has been reserved
[    0.407292] system 00:01: [io  0xffff] has been reserved
[    0.407355] system 00:01: [io  0x1c00-0x1cfe] has been reserved
[    0.407420] system 00:01: [io  0x1d00-0x1dfe] has been reserved
[    0.407484] system 00:01: [io  0x1e00-0x1efe] has been reserved
[    0.407549] system 00:01: [io  0x1f00-0x1ffe] has been reserved
[    0.407614] system 00:01: [io  0x1800-0x18fe] could not be reserved
[    0.407679] system 00:01: [io  0x164e-0x164f] has been reserved
[    0.407743] system 00:01: [io  0x3322-0x3323] has been reserved
[    0.407808] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.407832] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.407867] system 00:03: [io  0x1854-0x1857] has been reserved
[    0.407934] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.407955] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.408014] pnp 00:05: Plug and Play ACPI device, IDs SYN1212 PNP0f13 (active)
[    0.408049] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    0.408115] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.408389] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.408456] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.408522] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.408587] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.408653] system 00:07: [mem 0xf0000000-0xf7ffffff] has been reserved
[    0.408719] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.408784] system 00:07: [mem 0xfed90000-0xfed93fff] has been reserved
[    0.408850] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.408915] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
[    0.408981] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.409047] system 00:07: [mem 0xeffdf000-0xeffdffff] has been reserved
[    0.409113] system 00:07: [mem 0xeffe0000-0xeffeffff] has been reserved
[    0.409179] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.409307] pnp: PnP ACPI: found 8 devices
[    0.415358] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 02] add_size 1000
[    0.415360] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[    0.415361] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
[    0.415378] pci 0000:00:1c.4: bridge window [io  0x1000-0x0fff] to [bus 05-3d] add_size 1000
[    0.415382] pci 0000:00:1c.0: res[8]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[    0.415383] pci 0000:00:1c.0: res[9]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.415384] pci 0000:00:1c.0: res[7]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.415385] pci 0000:00:1c.4: res[7]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.415390] pci 0000:00:1c.0: BAR 8: assigned [mem 0xb2000000-0xb21fffff]
[    0.415461] pci 0000:00:1c.0: BAR 9: assigned [mem 0xb2200000-0xb23fffff 64bit pref]
[    0.415529] pci 0000:00:1c.0: BAR 7: assigned [io  0x2000-0x2fff]
[    0.415594] pci 0000:00:1c.4: BAR 7: assigned [io  0x4000-0x4fff]
[    0.415659] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.415722] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.415788] pci 0000:00:01.0:   bridge window [mem 0xeb000000-0xec0fffff]
[    0.415855] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.415923] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.415987] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    0.416055] pci 0000:00:1c.0:   bridge window [mem 0xb2000000-0xb21fffff]
[    0.416122] pci 0000:00:1c.0:   bridge window [mem 0xb2200000-0xb23fffff 64bit pref]
[    0.416193] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.416256] pci 0000:00:1c.2:   bridge window [io  0xd000-0xdfff]
[    0.416323] pci 0000:00:1c.2:   bridge window [mem 0xec200000-0xec2fffff]
[    0.416390] pci 0000:00:1c.2:   bridge window [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.416461] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.416526] pci 0000:00:1c.3:   bridge window [mem 0xec100000-0xec1fffff]
[    0.416596] pci 0000:00:1c.4: PCI bridge to [bus 05-3d]
[    0.416676] pci 0000:00:1c.4:   bridge window [io  0x4000-0x4fff]
[    0.416743] pci 0000:00:1c.4:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.416810] pci 0000:00:1c.4:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.416882] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.416883] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.416884] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.416885] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[    0.416886] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[    0.416887] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[    0.416888] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
[    0.416889] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
[    0.416890] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
[    0.416891] pci_bus 0000:00: resource 13 [mem 0x90000000-0xfeafffff]
[    0.416892] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.416893] pci_bus 0000:01: resource 1 [mem 0xeb000000-0xec0fffff]
[    0.416894] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.416895] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.416896] pci_bus 0000:02: resource 1 [mem 0xb2000000-0xb21fffff]
[    0.416897] pci_bus 0000:02: resource 2 [mem 0xb2200000-0xb23fffff 64bit pref]
[    0.416898] pci_bus 0000:03: resource 0 [io  0xd000-0xdfff]
[    0.416899] pci_bus 0000:03: resource 1 [mem 0xec200000-0xec2fffff]
[    0.416900] pci_bus 0000:03: resource 2 [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.416901] pci_bus 0000:04: resource 1 [mem 0xec100000-0xec1fffff]
[    0.416902] pci_bus 0000:05: resource 0 [io  0x4000-0x4fff]
[    0.416903] pci_bus 0000:05: resource 1 [mem 0xd4000000-0xea0fffff]
[    0.416904] pci_bus 0000:05: resource 2 [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.416950] NET: Registered protocol family 2
[    0.417161] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.417341] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.417503] TCP: Hash tables configured (established 131072 bind 65536)
[    0.417579] TCP: reno registered
[    0.417641] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.417733] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.417877] NET: Registered protocol family 1
[    0.418174] PCI: CLS mismatch (64 != 128), using 64 bytes
[    0.418273] pci 0000:01:00.0: Video device with shadowed ROM
[    0.418309] Trying to unpack rootfs image as initramfs...
[    0.771148] Freeing initrd memory: 3776K (ffff880037890000 - ffff880037c40000)
[    0.771223] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.771289] software IO TLB [mem 0x89c0b000-0x8dc0b000] (64MB) mapped at [ffff880089c0b000-ffff88008dc0afff]
[    0.771646] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[    0.772034] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.772140] audit: initializing netlink subsys (disabled)
[    0.772217] audit: type=2000 audit(1431319303.760:1): initialized
[    0.772549] VFS: Disk quotas dquot_6.5.2
[    0.772628] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.772875] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.772994] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    0.773289] ocfs2: Registered cluster interface o2cb
[    0.773379] OCFS2 User DLM kernel interface loaded
[    0.773700] gfs2: GFS2 installed
[    0.773925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.773995] io scheduler noop registered
[    0.774058] io scheduler deadline registered
[    0.774132] io scheduler cfq registered (default)
[    0.774716] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.775056] Linux agpgart interface v0.103
[    0.776063] brd: module loaded
[    0.776576] loop: module loaded
[    0.776706] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:SYNM] at 0x60,0x64 irq 1,12
[    1.300562] i8042: Detected active multiplexing controller, rev 1.1
[    1.302515] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.302579] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.302643] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.302706] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.302769] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.302909] mousedev: PS/2 mouse device common for all mice
[    1.303055] hidraw: raw HID events driver (C) Jiri Kosina
[    1.303321] TCP: cubic registered
[    1.303383] NET: Registered protocol family 17
[    1.303752] registered taskstats version 1
[    1.304401] Freeing unused kernel memory: 824K (ffffffff816d3000 - ffffffff817a1000)
[    1.306349] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.372753] libata version 3.00 loaded.
[    1.480809] ahci 0000:00:1f.2: version 3.0
[    1.480926] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    1.480949] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0xf impl SATA mode
[    1.480951] ahci 0000:00:1f.2: flags: 64bit ncq stag led clo pio slum part ems sxs apst 
[    1.538592] scsi host0: ahci
[    1.538676] scsi host1: ahci
[    1.538763] scsi host2: ahci
[    1.538843] scsi host3: ahci
[    1.538914] scsi host4: ahci
[    1.538994] scsi host5: ahci
[    1.539035] ata1: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316100 irq 25
[    1.539037] ata2: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316180 irq 25
[    1.539039] ata3: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316200 irq 25
[    1.539041] ata4: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316280 irq 25
[    1.539042] ata5: DUMMY
[    1.539042] ata6: DUMMY
[    1.768266] tsc: Refined TSC clocksource calibration: 2793.531 MHz
[    1.898442] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.899572] ata1.00: ATA-8: HGST HTS721010A9E630, JB0OA3J0, max UDMA/133
[    1.899573] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.900803] ata1.00: configured for UDMA/133
[    1.900870] scsi 0:0:0:0: Direct-Access     ATA      HGST HTS721010A9 A3J0 PQ: 0 ANSI: 5
[    1.901020] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    1.901022] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.901065] sd 0:0:0:0: [sda] Write Protect is off
[    1.901068] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.901089] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.964550]  sda: sda1 sda2
[    1.964731] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.308929] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.309902] ata2.00: ATA-8: Hitachi HTS545032B9SA02, PB3AC60W, max UDMA/133
[    2.309904] ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.311951] ata2.00: configured for UDMA/133
[    2.312005] scsi 1:0:0:0: Direct-Access     ATA      Hitachi HTS54503 C60W PQ: 0 ANSI: 5
[    2.312133] sd 1:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    2.312165] sd 1:0:0:0: [sdb] Write Protect is off
[    2.312167] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.312183] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.330562]  sdb: sdb1 sdb2
[    2.330727] sd 1:0:0:0: [sdb] Attached SCSI disk
[    2.649327] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.652940] ata3.00: ATAPI: TSSTcorp CDDVDW SN-208FB, TC00, max UDMA/100
[    2.655511] ata3.00: configured for UDMA/100
[    2.656820] scsi 2:0:0:0: CD-ROM            TSSTcorp CDDVDW SN-208FB  TC00 PQ: 0 ANSI: 5
[    2.703475] sr 2:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.703476] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.703551] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    2.750265] psmouse serio2: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00223/0x840300/0x122c00, board id: 1760, fw id: 1211538
[    2.769505] Switched to clocksource tsc
[    2.790276] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input6
[    3.049807] ata4: SATA link down (SStatus 0 SControl 300)
[    3.122315] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.122342] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    3.122365] sr 2:0:0:0: Attached scsi generic sg2 type 5
[    3.210066] scsi: <fdomain> Detection failed (no card)
[    3.321203] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[    3.375644] imm: Version 2.05 (for Linux 2.4.0)
[    3.542862] Fusion MPT base driver 3.04.20
[    3.542864] Copyright (c) 1999-2008 LSI Corporation
[    3.571385] Fusion MPT SPI Host driver 3.04.20
[    3.589431] Fusion MPT FC Host driver 3.04.20
[    3.608042] Fusion MPT SAS Host driver 3.04.20
[    3.623069] 3ware Storage Controller device driver for Linux v1.26.02.003.
[    3.637181] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[    3.652697] HP CISS Driver (v 3.6.26)
[    3.697811] Adaptec aacraid driver 1.2-0[30300]-ms
[    3.731067] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[    3.731920] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    3.763226] megasas: 06.805.06.01-rc1
[    3.780850] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.07.00.16-k.
[    3.810999] Emulex LightPulse Fibre Channel SCSI driver 10.4.8000.0.
[    3.811000] Copyright(c) 2004-2014 Emulex.  All rights reserved.
[    3.850286] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[    4.639356] ACPI: bus type USB registered
[    4.639376] usbcore: registered new interface driver usbfs
[    4.639386] usbcore: registered new interface driver hub
[    4.639407] usbcore: registered new device driver usb
[    4.640608] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.668757] usbcore: registered new interface driver usb-storage
[    4.694013] uhci_hcd: USB Universal Host Controller Interface driver
[    4.719226] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.770215] usbcore: registered new interface driver usbhid
[    4.770216] usbhid: USB HID core driver
[    5.025915] device-mapper: uevent: version 1.0.3
[    5.025959] device-mapper: ioctl: 4.29.0-ioctl (2014-10-28) initialised: dm-devel@redhat.com
[    5.246223] md: raid0 personality registered for level 0
[    5.273988] md: raid1 personality registered for level 1
[    5.310228] async_tx: api initialized (async)
[    5.482693] raid6: sse2x1    8589 MB/s
[    5.652891] raid6: sse2x2   11271 MB/s
[    5.823095] raid6: sse2x4   13191 MB/s
[    5.993298] raid6: avx2x1   16774 MB/s
[    6.163500] raid6: avx2x2   20158 MB/s
[    6.333704] raid6: avx2x4   23136 MB/s
[    6.333705] raid6: using algorithm avx2x4 (23136 MB/s)
[    6.333706] raid6: using avx2x2 recovery algorithm
[    6.350226] xor: automatically using best checksumming function:
[    6.443834]    avx       : 28139.200 MB/sec
[    6.448850] md: raid6 personality registered for level 6
[    6.448851] md: raid5 personality registered for level 5
[    6.448851] md: raid4 personality registered for level 4
[    6.479809] md: raid10 personality registered for level 10
[    6.508992] md: linear personality registered for level -1
[    6.538163] md: multipath personality registered for level -4
[    6.589563] Btrfs loaded
[    6.620635] JFS: nTxBlock = 8192, nTxLock = 65536
[    6.664501] RPC: Registered named UNIX socket transport module.
[    6.664503] RPC: Registered udp transport module.
[    6.664503] RPC: Registered tcp transport module.
[    6.664504] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    6.702001] fuse init (API version 7.23)
[    6.745178] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    6.745179] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    6.782997] pps_core: LinuxPPS API ver. 1 registered
[    6.782998] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    6.783835] PTP clock support registered
[    6.833499] Loading iSCSI transport class v2.0-870.
[    7.093021] UDF-fs: warning (device sdb2): udf_fill_super: No partition found (2)
[    7.099587] (mount,15222,0):ocfs2_fill_super:1054 ERROR: superblock probe failed!
[    7.099589] (mount,15222,0):ocfs2_fill_super:1245 ERROR: status = -22
[    7.099697] gfs2: gfs2 mount does not exist
[    7.099785] BTRFS: device fsid 59b3eb07-79cd-4973-ab94-ae247a4de533 devid 1 transid 2105 /dev/sdb2
[    7.100040] BTRFS info (device sdb2): disk space caching is enabled
[   10.700239] udevd[15617]: starting version 1.5.3
[   10.906437] random: udevd urandom read with 70 bits of entropy available
[   11.611284] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input9
[   11.611316] ACPI: Power Button [PWRB]
[   11.611354] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input10
[   11.611376] ACPI: Sleep Button [SLPB]
[   11.611414] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input11
[   11.611465] ACPI: Lid Switch [LID0]
[   11.611503] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input12
[   11.611535] ACPI: Power Button [PWRF]
[   11.611921] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[   11.611924] ACPI: Battery Slot [BAT0] (battery present)
[   11.699601] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[   11.699636] ACPI: AC Adapter [AC] (off-line)
[   11.811464] cfg80211: Calling CRDA to update world regulatory domain
[   11.857685] Monitor-Mwait will be used to enter C-1 state
[   11.857691] Monitor-Mwait will be used to enter C-2 state
[   11.857697] ACPI: acpi_idle registered with cpuidle
[   11.864870] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   11.864876] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[   11.864952] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[   11.865034] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   11.865036] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.865037] usb usb1: Product: xHCI Host Controller
[   11.865039] usb usb1: Manufacturer: Linux 3.19.3-1~exp1 xhci-hcd
[   11.865039] usb usb1: SerialNumber: 0000:00:14.0
[   11.865146] hub 1-0:1.0: USB hub found
[   11.865164] hub 1-0:1.0: 14 ports detected
[   11.867811] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   11.867814] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[   11.867887] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[   11.867889] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.867890] usb usb2: Product: xHCI Host Controller
[   11.867891] usb usb2: Manufacturer: Linux 3.19.3-1~exp1 xhci-hcd
[   11.867892] usb usb2: SerialNumber: 0000:00:14.0
[   11.867992] hub 2-0:1.0: USB hub found
[   11.868005] hub 2-0:1.0: 6 ports detected
[   11.870872] ehci-pci: EHCI PCI platform driver
[   11.870959] ehci-pci 0000:00:1a.0: EHCI Host Controller
[   11.870964] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
[   11.870974] ehci-pci 0000:00:1a.0: debug port 2
[   11.874888] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[   11.874900] ehci-pci 0000:00:1a.0: irq 16, io mem 0xec318000
[   11.890355] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[   11.890401] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[   11.890403] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.890404] usb usb3: Product: EHCI Host Controller
[   11.890405] usb usb3: Manufacturer: Linux 3.19.3-1~exp1 ehci_hcd
[   11.890406] usb usb3: SerialNumber: 0000:00:1a.0
[   11.890508] hub 3-0:1.0: USB hub found
[   11.890528] hub 3-0:1.0: 2 ports detected
[   11.890766] ehci-pci 0000:00:1d.0: EHCI Host Controller
[   11.890771] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
[   11.890781] ehci-pci 0000:00:1d.0: debug port 2
[   11.894687] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[   11.894697] ehci-pci 0000:00:1d.0: irq 23, io mem 0xec317000
[   11.910390] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[   11.910465] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[   11.910467] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.910468] usb usb4: Product: EHCI Host Controller
[   11.910469] usb usb4: Manufacturer: Linux 3.19.3-1~exp1 ehci_hcd
[   11.910470] usb usb4: SerialNumber: 0000:00:1d.0
[   11.910595] hub 4-0:1.0: USB hub found
[   11.910603] hub 4-0:1.0: 2 ports detected
[   11.991552] thermal LNXTHERM:00: registered as thermal_zone0
[   11.991554] ACPI: Thermal Zone [TZ0] (49 C)
[   12.099829] microcode: CPU0 sig=0x306c3, pf=0x10, revision=0x17
[   12.132590] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132617] microcode: CPU1 sig=0x306c3, pf=0x10, revision=0x17
[   12.132625] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132645] microcode: CPU2 sig=0x306c3, pf=0x10, revision=0x17
[   12.132651] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132657] microcode: CPU3 sig=0x306c3, pf=0x10, revision=0x17
[   12.132663] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132670] microcode: CPU4 sig=0x306c3, pf=0x10, revision=0x17
[   12.132677] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132697] microcode: CPU5 sig=0x306c3, pf=0x10, revision=0x17
[   12.132702] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132722] microcode: CPU6 sig=0x306c3, pf=0x10, revision=0x17
[   12.132727] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132734] microcode: CPU7 sig=0x306c3, pf=0x10, revision=0x17
[   12.132739] platform microcode: firmware: failed to load intel-ucode/06-3c-03 (-2)
[   12.132799] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[   12.189153] input: PC Speaker as /devices/platform/pcspkr/input/input13
[   12.190719] usb 1-3: new full-speed USB device number 2 using xhci_hcd
[   12.193805] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[   12.193811] r8169 0000:03:00.2: can't disable ASPM; OS doesn't have ASPM control
[   12.194521] r8169 0000:03:00.2 eth0: RTL8411 at 0xffffc9000931e000, 80:fa:5b:01:6d:12, XID 08800800 IRQ 27
[   12.194522] r8169 0000:03:00.2 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[   12.220786] usb 3-1: new high-speed USB device number 2 using ehci-pci
[   12.230796] usb 4-1: new high-speed USB device number 2 using ehci-pci
[   12.332453] usb 1-3: New USB device found, idVendor=1c7a, idProduct=0603
[   12.332456] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   12.332458] usb 1-3: Product: EgisTec_ES603
[   12.332459] usb 1-3: Manufacturer: EgisTec
[   12.370796] ACPI: Video Device [PEGP] (multi-head: yes  rom: no  post: no)
[   12.371284] usb 3-1: New USB device found, idVendor=8087, idProduct=8008
[   12.371286] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   12.371438] hub 3-1:1.0: USB hub found
[   12.371530] hub 3-1:1.0: 6 ports detected
[   12.382010] Intel(R) Wireless WiFi driver for Linux, in-tree:
[   12.382011] Copyright(c) 2003- 2014 Intel Corporation
[   12.461042] usb 1-7: new full-speed USB device number 3 using xhci_hcd
[   12.489514] snd_hda_intel 0000:01:00.1: Disabling MSI
[   12.607956] ACPI Warning: SystemIO range 0x000000000000f000-0x000000000000f01f conflicts with OpRegion 0x000000000000f000-0x000000000000f00f (\_SB_.PCI0.SBUS.SMBI) (20141107/utaddress-258)
[   12.607961] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.608106] acpi device:02: registered as cooling_device8
[   12.608225] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input14
[   12.608569] usb 4-1: New USB device found, idVendor=8087, idProduct=8000
[   12.608571] usb 4-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   12.609651] hub 4-1:1.0: USB hub found
[   12.609692] hub 4-1:1.0: 8 ports detected
[   12.612070] usb 1-7: New USB device found, idVendor=8087, idProduct=07dc
[   12.612073] usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   12.671846] [drm] Initialized drm 1.1.0 20060810
[   12.682778] sound hdaudioC0D0: autoconfig: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:line
[   12.682780] sound hdaudioC0D0:    speaker_outs=1 (0x14/0x0/0x0/0x0/0x0)
[   12.682781] sound hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   12.682782] sound hdaudioC0D0:    mono: mono_out=0x0
[   12.682783] sound hdaudioC0D0:    dig-out=0x1e/0x0
[   12.682784] sound hdaudioC0D0:    inputs:
[   12.682785] sound hdaudioC0D0:      Mic=0x18
[   12.682787] sound hdaudioC0D0:      Internal Mic=0x12
[   12.682788] sound hdaudioC0D0:      Line=0x1a
[   12.690624] random: nonblocking pool is initialized
[   12.849800] iwlwifi 0000:04:00.0: firmware: direct-loading firmware iwlwifi-3160-12.ucode
[   12.849929] iwlwifi 0000:04:00.0: loaded firmware version 25.15.12.0 op_mode iwlmvm
[   13.131871] sound hdaudioC1D0: autoconfig: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[   13.131874] sound hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   13.131875] sound hdaudioC1D0:    hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   13.131876] sound hdaudioC1D0:    mono: mono_out=0x0
[   13.131877] sound hdaudioC1D0:    dig-out=0x5/0x7
[   13.131877] sound hdaudioC1D0:    inputs:
[   13.138817] Bluetooth: Core ver 2.20
[   13.138824] NET: Registered protocol family 31
[   13.138824] Bluetooth: HCI device and connection manager initialized
[   13.138827] Bluetooth: HCI socket layer initialized
[   13.138829] Bluetooth: L2CAP socket layer initialized
[   13.138830] Bluetooth: SCO socket layer initialized
[   13.320704] nvidia: module license 'NVIDIA' taints kernel.
[   13.320706] Disabling lock debugging due to kernel taint
[   13.327873] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   13.328089] [drm] Initialized nvidia-drm 0.0.0 20150116 for 0000:01:00.0 on minor 0
[   13.328092] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  349.16  Wed Apr  8 00:17:22 PDT 2015
[   13.348503] usbcore: registered new interface driver btusb
[   13.361119] Bluetooth: hci0: read Intel version: 370710010002030d00
[   13.362988] iwlwifi 0000:04:00.0: Detected Intel(R) Dual Band Wireless AC 3160, REV=0x164
[   13.363035] iwlwifi 0000:04:00.0: L1 Disabled - LTR Disabled
[   13.363258] iwlwifi 0000:04:00.0: L1 Disabled - LTR Disabled
[   13.422969] bluetooth hci0: firmware: direct-loading firmware intel/ibt-hw-37.7.10-fw-1.0.2.3.d.bseq
[   13.422974] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.0.2.3.d.bseq
[   13.550323] Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
[   13.593299] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[   13.749580] cfg80211: World regulatory domain updated:
[   13.749581] cfg80211:  DFS Master region: unset
[   13.749582] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   13.749584] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   13.749586] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   13.749587] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   13.749588] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   13.749589] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   13.749591] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   13.749592] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   13.749593] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   13.930671] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   13.930699] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   13.930715] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   13.930738] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   13.930754] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   13.930779] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   13.930795] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   13.930809] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   14.102525] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   14.102573] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   14.403935] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   15.692052] BTRFS info (device sdb2): disk space caching is enabled
[   15.828348] Adding 4194300k swap on /dev/sda2.  Priority:-1 extents:1 across:4194300k 
[   18.690891] iwlwifi 0000:04:00.0: L1 Disabled - LTR Disabled
[   18.691115] iwlwifi 0000:04:00.0: L1 Disabled - LTR Disabled
[   19.204186] r8169 0000:03:00.2: firmware: direct-loading firmware rtl_nic/rtl8411-1.fw
[   19.302150] r8169 0000:03:00.2 eth0: link down
[   19.467653] NET: Registered protocol family 10
[   19.467881] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.467909] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   23.341273] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.341308] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.341324] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.341348] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.341363] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.341389] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.341404] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.341419] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.404482] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.404519] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[   23.455530] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[  110.137496] wlan0: authenticate with 28:cf:da:b0:d2:68
[  110.140943] wlan0: send auth to 28:cf:da:b0:d2:68 (try 1/3)
[  110.141366] wlan0: authenticated
[  110.147906] wlan0: associate with 28:cf:da:b0:d2:68 (try 1/3)
[  110.148762] wlan0: RX AssocResp from 28:cf:da:b0:d2:68 (capab=0x511 status=0 aid=2)
[  110.149982] wlan0: associated
[  110.150010] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  110.150063] cfg80211: Calling CRDA for country: US
[  110.150140] wlan0: deauthenticating from 28:cf:da:b0:d2:68 by local choice (Reason: 3=DEAUTH_LEAVING)
[  110.152463] cfg80211: Calling CRDA to update world regulatory domain
[  110.153960] cfg80211: World regulatory domain updated:
[  110.153962] cfg80211:  DFS Master region: unset
[  110.153962] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  110.153964] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  110.153966] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  110.153967] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[  110.153968] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[  110.153970] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[  110.153971] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  110.153972] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[  110.153973] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[  116.689880] wlan0: authenticate with 28:cf:da:b0:d2:67
[  116.692713] wlan0: send auth to 28:cf:da:b0:d2:67 (try 1/3)
[  116.694480] wlan0: authenticated
[  116.695712] wlan0: associate with 28:cf:da:b0:d2:67 (try 1/3)
[  116.699189] wlan0: RX AssocResp from 28:cf:da:b0:d2:67 (capab=0x431 status=0 aid=11)
[  116.699909] wlan0: associated
[  116.699971] cfg80211: Calling CRDA for country: US
[  116.700018] wlan0: deauthenticating from 28:cf:da:b0:d2:67 by local choice (Reason: 3=DEAUTH_LEAVING)
[  116.702181] cfg80211: Calling CRDA to update world regulatory domain
[  116.703515] cfg80211: World regulatory domain updated:
[  116.703516] cfg80211:  DFS Master region: unset
[  116.703517] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  116.703519] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  116.703520] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  116.703521] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[  116.703523] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[  116.703524] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[  116.703525] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  116.703526] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[  116.703528] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[  123.239152] wlan0: authenticate with 28:cf:da:b0:d2:68
[  123.241905] wlan0: send auth to 28:cf:da:b0:d2:68 (try 1/3)
[  123.243069] wlan0: authenticated
[  123.243523] wlan0: associate with 28:cf:da:b0:d2:68 (try 1/3)
[  123.245457] wlan0: RX AssocResp from 28:cf:da:b0:d2:68 (capab=0x511 status=0 aid=2)
[  123.246390] wlan0: associated
[  123.246434] cfg80211: Calling CRDA for country: US
[  123.246499] wlan0: deauthenticating from 28:cf:da:b0:d2:68 by local choice (Reason: 3=DEAUTH_LEAVING)
[  123.248903] cfg80211: Calling CRDA to update world regulatory domain
[  123.250252] cfg80211: World regulatory domain updated:
[  123.250253] cfg80211:  DFS Master region: unset
[  123.250254] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  123.250256] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  123.250257] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  123.250258] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[  123.250260] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[  123.250261] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[  123.250262] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  123.250263] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[  123.250264] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[  129.786691] wlan0: authenticate with 28:cf:da:b0:d2:67
[  129.788633] wlan0: send auth to 28:cf:da:b0:d2:67 (try 1/3)
[  129.790312] wlan0: authenticated
[  129.796933] wlan0: associate with 28:cf:da:b0:d2:67 (try 1/3)
[  129.803723] wlan0: RX AssocResp from 28:cf:da:b0:d2:67 (capab=0x431 status=0 aid=11)
[  129.804083] wlan0: associated
[  129.804144] cfg80211: Calling CRDA for country: US
[  129.804213] wlan0: deauthenticating from 28:cf:da:b0:d2:67 by local choice (Reason: 3=DEAUTH_LEAVING)
[  129.806516] cfg80211: Regulatory domain changed to country: US
[  129.806518] cfg80211:  DFS Master region: unset
[  129.806519] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  129.806520] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[  129.806522] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[  129.806523] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[  129.806525] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[  129.806526] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[  129.806527] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[  129.806670] cfg80211: Calling CRDA to update world regulatory domain
[  129.807841] cfg80211: World regulatory domain updated:
[  129.807842] cfg80211:  DFS Master region: unset
[  129.807843] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  129.807845] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  129.807846] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  129.807847] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[  129.807848] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[  129.807850] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[  129.807851] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  129.807852] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[  129.807853] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[  134.686477] traps: gom-flickr-mine[17586] trap int3 ip:7fed6f1bf13a sp:7ffc9307c680 error:0
[  220.219398] wlan0: authenticate with 3c:ea:4f:d2:0d:f9
[  220.221881] wlan0: send auth to 3c:ea:4f:d2:0d:f9 (try 1/3)
[  220.223513] wlan0: authenticated
[  220.223651] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[  220.223653] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[  220.229536] wlan0: associate with 3c:ea:4f:d2:0d:f9 (try 1/3)
[  220.231657] wlan0: RX AssocResp from 3c:ea:4f:d2:0d:f9 (capab=0x431 status=0 aid=1)
[  220.233003] wlan0: associated
[  220.233054] cfg80211: Calling CRDA for country: US
[  220.233101] wlan0: deauthenticating from 3c:ea:4f:d2:0d:f9 by local choice (Reason: 3=DEAUTH_LEAVING)
[  220.236192] cfg80211: Calling CRDA to update world regulatory domain
[  220.237488] cfg80211: World regulatory domain updated:
[  220.237489] cfg80211:  DFS Master region: unset
[  220.237490] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  220.237492] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  220.237493] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  220.237494] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[  220.237495] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[  220.237497] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[  220.237498] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  220.237499] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[  220.237500] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[  229.972901] wlan0: authenticate with 3c:ea:4f:d2:0d:f9
[  229.975122] wlan0: send auth to 3c:ea:4f:d2:0d:f9 (try 1/3)
[  229.976758] wlan0: authenticated
[  229.976884] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[  229.976885] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[  229.981195] wlan0: associate with 3c:ea:4f:d2:0d:f9 (try 1/3)
[  229.983406] wlan0: RX AssocResp from 3c:ea:4f:d2:0d:f9 (capab=0x431 status=0 aid=1)
[  229.984668] wlan0: associated
[  229.984720] cfg80211: Calling CRDA for country: US
[  229.984774] wlan0: deauthenticating from 3c:ea:4f:d2:0d:f9 by local choice (Reason: 3=DEAUTH_LEAVING)
[  229.988174] cfg80211: Calling CRDA to update world regulatory domain
[  229.989758] cfg80211: World regulatory domain updated:
[  229.989759] cfg80211:  DFS Master region: unset
[  229.989760] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  229.989762] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  229.989763] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  229.989764] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[  229.989766] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[  229.989767] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[  229.989768] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  229.989769] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[  229.989770] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[  252.525068] traps: gom-flickr-mine[17734] trap int3 ip:7f62f4ea513a sp:7fff001a4cf0 error:0

Thanks again!

caseycole589 · May 11, 2015

intel wifi drivers need to be built in to kernel, when you use genkernel it builds them as modules at least last time I used it, It gave me problems before to do a genkernel with nconfig options go to the intel wifi driver and make sure there is a * and not M.

allen286 · May 12, 2015

I was for some reason unable to directly include the driver... It says that it depends on things being built as modules, so it will be built as a module. Any way to find these dependencies? I think you're on the right track; I never thought to check this.

666threesixes666 · May 12, 2015

per gentoo wiki

intel Wireless 3160 iwlwifi sys-firmware/iwl3160-ucode or sys-kernel/linux-firmware Requires kernel parameter Device-Drivers->Network device support->Wireless LAN->Intel Wireless WiFi MVM Firmware support

Tassie_Tux · May 12, 2015

Following recent networkmanager and/or wpa_supplicant updates I have experienced the exact same issue on two computers, both with intel wireless drivers (different model controllers).

At least one has the kernel drivers built as modules. As suggested above I will rebuild the kernel with built-in drivers and report back.

allen286 · May 12, 2015

So the kernel I'm using has Intel Wireless WiFi MVM Firmware support, but it is compiled as a module. When trying to switch to built in, I get a message that says "This feature depends on another which has been configured as a module. As a result, this feature will be built as a module." Maybe I should use an older version of wpa_supplicant?

666threesixes666 · May 12, 2015

post the exact message, set the higher up driver as a Y then the lower driver should also be able to be set as Y

allen286 · May 12, 2015

Unfortunately, I did post the exact message... However, I did figure it out. I managed to get the (*) in the correct spots in genkernel, but the problem has been made worse by this... Now the driver does not load. Here's my new dmesg output:

[    0.000000]   Normal   [mem 0x0000000100000000-0x000000046effffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009cfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x000000007d21efff]
[    0.000000]   node   0: [mem 0x000000007d226000-0x000000007d980fff]
[    0.000000]   node   0: [mem 0x000000007dbee000-0x000000008dc0afff]
[    0.000000]   node   0: [mem 0x000000008e10b000-0x000000008e675fff]
[    0.000000]   node   0: [mem 0x000000008efff000-0x000000008effffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000046effffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000046effffff]
[    0.000000] On node 0 totalpages: 4181663
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 7893 pages used for memmap
[    0.000000]   DMA32 zone: 577283 pages, LIFO batch:31
[    0.000000]   Normal zone: 49224 pages used for memmap
[    0.000000]   Normal zone: 3600384 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x1808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x7d21f000-0x7d225fff]
[    0.000000] PM: Registered nosave memory: [mem 0x7d981000-0x7dbedfff]
[    0.000000] PM: Registered nosave memory: [mem 0x8dc0b000-0x8e10afff]
[    0.000000] PM: Registered nosave memory: [mem 0x8e676000-0x8e7aafff]
[    0.000000] PM: Registered nosave memory: [mem 0x8e7ab000-0x8effefff]
[    0.000000] PM: Registered nosave memory: [mem 0x8f000000-0xefffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.000000] e820: [mem 0x8f000000-0xefffffff] available for PCI devices
[    0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 29 pages/cpu @ffff88046ec00000 s78488 r8192 d32104 u262144
[    0.000000] pcpu-alloc: s78488 r8192 d32104 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 4124469
[    0.000000] Kernel command line: BOOT_IMAGE=/kernel-genkernel-x86_64-4.0.2-gentoo root=/dev/sdb2
[    0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] log_buf_len total cpu_extra contributions: 28672 bytes
[    0.000000] log_buf_len min size: 32768 bytes
[    0.000000] log_buf_len: 65536 bytes
[    0.000000] early log buf free: 20076(61%)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 16388148K/16726652K available (7379K kernel code, 415K rwdata, 2316K rodata, 844K init, 836K bss, 338504K reserved, 0K cma-reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Additional per-CPU info printed with stalls.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=8.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS:4352 nr_irqs:488 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2793.339 MHz processor
[    0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 5586.67 BogoMIPS (lpj=27933390)
[    0.000131] pid_max: default: 32768 minimum: 301
[    0.000197] ACPI: Core revision 20150204
[    0.008360] ACPI: All ACPI Tables successfully acquired
[    0.018121] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.018187] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.018444] CPU: Physical Processor ID: 0
[    0.018505] CPU: Processor Core ID: 0
[    0.018568] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.018633] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.019523] mce: CPU supports 9 MCE banks
[    0.019596] CPU0: Thermal monitoring enabled (TM1)
[    0.019665] process: using mwait in idle threads
[    0.019730] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
[    0.019795] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[    0.019958] Freeing SMP alternatives memory: 32K (ffffffff81ab7000 - ffffffff81abf000)
[    0.020381] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.120566] TSC deadline timer enabled
[    0.120568] smpboot: CPU0: Intel(R) Core(TM) i7-4810MQ CPU @ 2.80GHz (fam: 06, model: 3c, stepping: 03)
[    0.120795] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[    0.121118] ... version:                3
[    0.121179] ... bit width:              48
[    0.121241] ... generic registers:      4
[    0.121303] ... value mask:             0000ffffffffffff
[    0.121366] ... max period:             0000ffffffffffff
[    0.121430] ... fixed-purpose events:   3
[    0.121491] ... event mask:             000000070000000f
[    0.121753] x86: Booting SMP configuration:
[    0.121815] .... node  #0, CPUs:      #1 #2 #3 #4 #5 #6 #7
[    0.220926] x86: Booted up 1 node, 8 CPUs
[    0.221048] smpboot: Total of 8 processors activated (44693.42 BogoMIPS)
[    0.226770] devtmpfs: initialized
[    0.227010] PM: Registering ACPI NVS region [mem 0x7d21f000-0x7d225fff] (28672 bytes)
[    0.227079] PM: Registering ACPI NVS region [mem 0x8e676000-0x8e7aafff] (1265664 bytes)
[    0.227284] xor: automatically using best checksumming function:
[    0.326769]    avx       : 24949.600 MB/sec
[    0.326924] NET: Registered protocol family 16
[    0.386867] cpuidle: using governor ladder
[    0.466976] cpuidle: using governor menu
[    0.470002] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.470068] ACPI: bus type PCI registered
[    0.470193] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[    0.470275] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[    0.470408] PCI: Using configuration type 1 for base access
[    0.717295] raid6: sse2x1    8545 MB/s
[    0.887502] raid6: sse2x2   11055 MB/s
[    1.057707] raid6: sse2x4   13120 MB/s
[    1.227910] raid6: avx2x1   16688 MB/s
[    1.398117] raid6: avx2x2   19710 MB/s
[    1.568320] raid6: avx2x4   22943 MB/s
[    1.568381] raid6: using algorithm avx2x4 (22943 MB/s)
[    1.568443] raid6: using avx2x2 recovery algorithm
[    1.568547] ACPI: Added _OSI(Module Device)
[    1.568609] ACPI: Added _OSI(Processor Device)
[    1.568670] ACPI: Added _OSI(3.0 _SCP Extensions)
[    1.568732] ACPI: Added _OSI(Processor Aggregator Device)
[    1.571526] ACPI: Executed 1 blocks of module-level executable AML code
[    1.573639] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    1.574357] ACPI: Dynamic OEM Table Load:
[    1.574512] ACPI: SSDT 0xFFFF88045DD78400 0003D3 (v01 PmRef  Cpu0Cst  00003001 INTL 20120711)
[    1.575174] ACPI: Dynamic OEM Table Load:
[    1.575329] ACPI: SSDT 0xFFFF88045D8F3000 0005AA (v01 PmRef  ApIst    00003000 INTL 20120711)
[    1.576028] ACPI: Dynamic OEM Table Load:
[    1.576183] ACPI: SSDT 0xFFFF88045DED8C00 000119 (v01 PmRef  ApCst    00003000 INTL 20120711)
[    1.581199] ACPI: Interpreter enabled
[    1.581267] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150204/hwxface-580)
[    1.581443] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150204/hwxface-580)
[    1.581627] ACPI: (supports S0 S3 S4 S5)
[    1.581689] ACPI: Using IOAPIC for interrupt routing
[    1.581773] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    1.587850] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
[    1.587918] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    1.588086] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug PME]
[    1.588241] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
[    1.588478] PCI host bridge to bus 0000:00
[    1.588541] pci_bus 0000:00: root bus resource [bus 00-7e]
[    1.588605] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    1.588672] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    1.588737] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    1.588805] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[    1.588871] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[    1.588939] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[    1.589005] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[    1.589072] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[    1.589139] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[    1.589206] pci_bus 0000:00: root bus resource [mem 0x90000000-0xfeafffff window]
[    1.589278] pci 0000:00:00.0: [8086:0c04] type 00 class 0x060000
[    1.589349] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
[    1.589379] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    1.589413] pci 0000:00:01.0: System wakeup disabled by ACPI
[    1.589534] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[    1.589551] pci 0000:00:14.0: reg 0x10: [mem 0xec300000-0xec30ffff 64bit]
[    1.589606] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    1.589633] pci 0000:00:14.0: System wakeup disabled by ACPI
[    1.589731] pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
[    1.589748] pci 0000:00:16.0: reg 0x10: [mem 0xec31a000-0xec31a00f 64bit]
[    1.589807] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    1.589874] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[    1.589892] pci 0000:00:1a.0: reg 0x10: [mem 0xec318000-0xec3183ff]
[    1.589974] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    1.590012] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    1.590112] pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
[    1.590126] pci 0000:00:1b.0: reg 0x10: [mem 0xec310000-0xec313fff 64bit]
[    1.590189] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    1.590217] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    1.590313] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
[    1.590375] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    1.590404] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    1.590501] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400
[    1.590563] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    1.590592] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    1.590688] pci 0000:00:1c.3: [8086:8c16] type 01 class 0x060400
[    1.590749] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    1.590779] pci 0000:00:1c.3: System wakeup disabled by ACPI
[    1.590874] pci 0000:00:1c.4: [8086:8c18] type 01 class 0x060400
[    1.590943] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    1.590973] pci 0000:00:1c.4: System wakeup disabled by ACPI
[    1.591075] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[    1.591093] pci 0000:00:1d.0: reg 0x10: [mem 0xec317000-0xec3173ff]
[    1.591175] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    1.591212] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    1.591311] pci 0000:00:1f.0: [8086:8c4b] type 00 class 0x060100
[    1.591458] pci 0000:00:1f.2: [8086:8c03] type 00 class 0x010601
[    1.591471] pci 0000:00:1f.2: reg 0x10: [io  0xf070-0xf077]
[    1.591477] pci 0000:00:1f.2: reg 0x14: [io  0xf060-0xf063]
[    1.591483] pci 0000:00:1f.2: reg 0x18: [io  0xf050-0xf057]
[    1.591489] pci 0000:00:1f.2: reg 0x1c: [io  0xf040-0xf043]
[    1.591495] pci 0000:00:1f.2: reg 0x20: [io  0xf020-0xf03f]
[    1.591501] pci 0000:00:1f.2: reg 0x24: [mem 0xec316000-0xec3167ff]
[    1.591535] pci 0000:00:1f.2: PME# supported from D3hot
[    1.591589] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[    1.591601] pci 0000:00:1f.3: reg 0x10: [mem 0xec315000-0xec3150ff 64bit]
[    1.591618] pci 0000:00:1f.3: reg 0x20: [io  0xf000-0xf01f]
[    1.591714] pci 0000:01:00.0: [10de:119a] type 00 class 0x030000
[    1.591724] pci 0000:01:00.0: reg 0x10: [mem 0xeb000000-0xebffffff]
[    1.591734] pci 0000:01:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    1.591743] pci 0000:01:00.0: reg 0x1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[    1.591750] pci 0000:01:00.0: reg 0x24: [io  0xe000-0xe07f]
[    1.591756] pci 0000:01:00.0: reg 0x30: [mem 0xec000000-0xec07ffff pref]
[    1.591810] pci 0000:01:00.0: System wakeup disabled by ACPI
[    1.591909] pci 0000:01:00.1: [10de:0e0a] type 00 class 0x040300
[    1.591919] pci 0000:01:00.1: reg 0x10: [mem 0xec080000-0xec083fff]
[    1.608382] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.608446] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    1.608448] pci 0000:00:01.0:   bridge window [mem 0xeb000000-0xec0fffff]
[    1.608450] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    1.608494] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    1.608623] pci 0000:03:00.0: [10ec:5289] type 00 class 0xff0000
[    1.608641] pci 0000:03:00.0: reg 0x10: [mem 0xec200000-0xec20ffff]
[    1.608780] pci 0000:03:00.0: supports D1 D2
[    1.608781] pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
[    1.608808] pci 0000:03:00.0: System wakeup disabled by ACPI
[    1.608915] pci 0000:03:00.2: [10ec:8168] type 00 class 0x020000
[    1.608933] pci 0000:03:00.2: reg 0x10: [io  0xd000-0xd0ff]
[    1.608960] pci 0000:03:00.2: reg 0x18: [mem 0xd2104000-0xd2104fff 64bit pref]
[    1.608976] pci 0000:03:00.2: reg 0x20: [mem 0xd2100000-0xd2103fff 64bit pref]
[    1.609057] pci 0000:03:00.2: supports D1 D2
[    1.609058] pci 0000:03:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[    1.609084] pci 0000:03:00.2: System wakeup disabled by ACPI
[    1.628412] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    1.628476] pci 0000:00:1c.2:   bridge window [io  0xd000-0xdfff]
[    1.628478] pci 0000:00:1c.2:   bridge window [mem 0xec200000-0xec2fffff]
[    1.628482] pci 0000:00:1c.2:   bridge window [mem 0xd2100000-0xd21fffff 64bit pref]
[    1.628553] pci 0000:04:00.0: [8086:08b3] type 00 class 0x028000
[    1.628589] pci 0000:04:00.0: reg 0x10: [mem 0xec100000-0xec101fff 64bit]
[    1.628775] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[    1.628805] pci 0000:04:00.0: System wakeup disabled by ACPI
[    1.648436] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    1.648502] pci 0000:00:1c.3:   bridge window [mem 0xec100000-0xec1fffff]
[    1.648551] pci 0000:00:1c.4: PCI bridge to [bus 05-3d]
[    1.648618] pci 0000:00:1c.4:   bridge window [mem 0xd4000000-0xea0fffff]
[    1.648622] pci 0000:00:1c.4:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    1.648651] pci_bus 0000:00: on NUMA node 0
[    1.648652] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
[    1.649245] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[    1.649838] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    1.650429] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 10 11 12 14 15)
[    1.651018] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 10 11 12 14 15)
[    1.651607] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    1.652291] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    1.652971] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 10 11 12 14 15)
[    1.653559] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[    1.654325] ACPI: Enabled 5 GPEs in block 00 to 3F
[    1.654504] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    1.654620] vgaarb: setting as boot device: PCI:0000:01:00.0
[    1.654684] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    1.654751] vgaarb: loaded
[    1.654810] vgaarb: bridge control possible 0000:01:00.0
[    1.654927] SCSI subsystem initialized
[    1.655008] pps_core: LinuxPPS API ver. 1 registered
[    1.655070] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.655155] PTP clock support registered
[    1.655273] PCI: Using ACPI for IRQ routing
[    1.658136] PCI: pci_cache_line_size set to 64 bytes
[    1.658184] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[    1.658185] e820: reserve RAM buffer [mem 0x7d21f000-0x7fffffff]
[    1.658186] e820: reserve RAM buffer [mem 0x7d981000-0x7fffffff]
[    1.658187] e820: reserve RAM buffer [mem 0x8dc0b000-0x8fffffff]
[    1.658188] e820: reserve RAM buffer [mem 0x8e676000-0x8fffffff]
[    1.658189] e820: reserve RAM buffer [mem 0x8f000000-0x8fffffff]
[    1.658190] e820: reserve RAM buffer [mem 0x46f000000-0x46fffffff]
[    1.658287] NET: Registered protocol family 23
[    1.658403] cfg80211: Calling CRDA to update world regulatory domain
[    1.658547] Switched to clocksource hpet
[    1.660059] pnp: PnP ACPI init
[    1.660172] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[    1.660240] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    1.660377] system 00:01: [io  0x0680-0x069f] has been reserved
[    1.660443] system 00:01: [io  0xffff] has been reserved
[    1.660507] system 00:01: [io  0xffff] has been reserved
[    1.660573] system 00:01: [io  0xffff] has been reserved
[    1.660637] system 00:01: [io  0x1c00-0x1cfe] has been reserved
[    1.660701] system 00:01: [io  0x1d00-0x1dfe] has been reserved
[    1.660765] system 00:01: [io  0x1e00-0x1efe] has been reserved
[    1.660830] system 00:01: [io  0x1f00-0x1ffe] has been reserved
[    1.660894] system 00:01: [io  0x1800-0x18fe] could not be reserved
[    1.660959] system 00:01: [io  0x164e-0x164f] has been reserved
[    1.661023] system 00:01: [io  0x3322-0x3323] has been reserved
[    1.661088] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.661111] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.661148] system 00:03: [io  0x1854-0x1857] has been reserved
[    1.661215] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    1.661237] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    1.661297] pnp 00:05: Plug and Play ACPI device, IDs SYN1212 PNP0f13 (active)
[    1.661333] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    1.661400] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.661677] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    1.661745] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
[    1.661810] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
[    1.661875] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
[    1.661941] system 00:07: [mem 0xf0000000-0xf7ffffff] has been reserved
[    1.662010] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
[    1.662075] system 00:07: [mem 0xfed90000-0xfed93fff] has been reserved
[    1.662141] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved
[    1.662206] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
[    1.662272] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
[    1.662337] system 00:07: [mem 0xeffdf000-0xeffdffff] has been reserved
[    1.662403] system 00:07: [mem 0xeffe0000-0xeffeffff] has been reserved
[    1.662469] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.662598] pnp: PnP ACPI: found 8 devices
[    1.667202] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 02] add_size 1000
[    1.667203] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[    1.667205] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
[    1.667221] pci 0000:00:1c.4: bridge window [io  0x1000-0x0fff] to [bus 05-3d] add_size 1000
[    1.667224] pci 0000:00:1c.0: res[8]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[    1.667225] pci 0000:00:1c.0: res[9]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    1.667227] pci 0000:00:1c.0: res[7]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    1.667228] pci 0000:00:1c.4: res[7]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    1.667232] pci 0000:00:1c.0: BAR 8: assigned [mem 0xb2000000-0xb21fffff]
[    1.667303] pci 0000:00:1c.0: BAR 9: assigned [mem 0xb2200000-0xb23fffff 64bit pref]
[    1.667371] pci 0000:00:1c.0: BAR 7: assigned [io  0x2000-0x2fff]
[    1.667436] pci 0000:00:1c.4: BAR 7: assigned [io  0x4000-0x4fff]
[    1.667502] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.667566] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    1.667631] pci 0000:00:01.0:   bridge window [mem 0xeb000000-0xec0fffff]
[    1.667698] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    1.667766] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    1.667829] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    1.667896] pci 0000:00:1c.0:   bridge window [mem 0xb2000000-0xb21fffff]
[    1.667963] pci 0000:00:1c.0:   bridge window [mem 0xb2200000-0xb23fffff 64bit pref]
[    1.668033] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    1.668097] pci 0000:00:1c.2:   bridge window [io  0xd000-0xdfff]
[    1.668163] pci 0000:00:1c.2:   bridge window [mem 0xec200000-0xec2fffff]
[    1.668230] pci 0000:00:1c.2:   bridge window [mem 0xd2100000-0xd21fffff 64bit pref]
[    1.668301] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    1.668366] pci 0000:00:1c.3:   bridge window [mem 0xec100000-0xec1fffff]
[    1.668450] pci 0000:00:1c.4: PCI bridge to [bus 05-3d]
[    1.668517] pci 0000:00:1c.4:   bridge window [io  0x4000-0x4fff]
[    1.668596] pci 0000:00:1c.4:   bridge window [mem 0xd4000000-0xea0fffff]
[    1.668663] pci 0000:00:1c.4:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    1.668734] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    1.668736] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    1.668737] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    1.668738] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[    1.668739] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[    1.668740] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[    1.668741] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[    1.668742] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff window]
[    1.668743] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff window]
[    1.668744] pci_bus 0000:00: resource 13 [mem 0x90000000-0xfeafffff window]
[    1.668745] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    1.668746] pci_bus 0000:01: resource 1 [mem 0xeb000000-0xec0fffff]
[    1.668747] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[    1.668748] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    1.668749] pci_bus 0000:02: resource 1 [mem 0xb2000000-0xb21fffff]
[    1.668751] pci_bus 0000:02: resource 2 [mem 0xb2200000-0xb23fffff 64bit pref]
[    1.668752] pci_bus 0000:03: resource 0 [io  0xd000-0xdfff]
[    1.668753] pci_bus 0000:03: resource 1 [mem 0xec200000-0xec2fffff]
[    1.668754] pci_bus 0000:03: resource 2 [mem 0xd2100000-0xd21fffff 64bit pref]
[    1.668755] pci_bus 0000:04: resource 1 [mem 0xec100000-0xec1fffff]
[    1.668756] pci_bus 0000:05: resource 0 [io  0x4000-0x4fff]
[    1.668757] pci_bus 0000:05: resource 1 [mem 0xd4000000-0xea0fffff]
[    1.668758] pci_bus 0000:05: resource 2 [mem 0x90000000-0xb1ffffff 64bit pref]
[    1.668804] NET: Registered protocol family 2
[    1.669007] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    1.669187] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    1.669351] TCP: Hash tables configured (established 131072 bind 65536)
[    1.669428] TCP: reno registered
[    1.669489] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    1.669581] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    1.669727] NET: Registered protocol family 1
[    1.670022] PCI: CLS mismatch (64 != 128), using 64 bytes
[    1.670122] pci 0000:01:00.0: Video device with shadowed ROM
[    1.670160] Trying to unpack rootfs image as initramfs...
[    1.983220] Freeing initrd memory: 3320K (ffff880037974000 - ffff880037cb2000)
[    1.983293] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.983359] software IO TLB [mem 0x89c0b000-0x8dc0b000] (64MB) mapped at [ffff880089c0b000-ffff88008dc0afff]
[    1.983723] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[    1.984116] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    1.984221] audit: initializing netlink subsys (disabled)
[    1.984295] audit: type=2000 audit(1431401823.980:1): initialized
[    1.984617] VFS: Disk quotas dquot_6.5.2
[    1.984698] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.984937] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.985054] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    1.985335] ocfs2: Registered cluster interface o2cb
[    1.985424] OCFS2 User DLM kernel interface loaded
[    1.985756] gfs2: GFS2 installed
[    1.986141] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.986212] io scheduler noop registered
[    1.986275] io scheduler deadline registered
[    1.986349] io scheduler cfq registered (default)
[    1.986948] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.987325] Linux agpgart interface v0.103
[    1.988573] brd: module loaded
[    1.989464] loop: module loaded
[    1.989561] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    1.992293] e100: Copyright(c) 1999-2006 Intel Corporation
[    1.992371] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    1.992439] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    1.992518] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.992583] e1000e: Copyright(c) 1999 - 2014 Intel Corporation.
[    1.992660] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.15-k
[    1.992728] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.992805] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k
[    1.992873] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.992949] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.0.1-k
[    1.993017] ixgbe: Copyright (c) 1999-2014 Intel Corporation.
[    1.993093] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver - version 2.12.1-k
[    1.993177] ixgbevf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.993252] i40e: Intel(R) Ethernet Connection XL710 Network Driver - version 1.2.6-k
[    1.993321] i40e: Copyright (c) 2013 - 2014 Intel Corporation.
[    1.993397] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[    1.993465] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[    1.993540] i40evf: Intel(R) XL710/X710 Virtual Function Network Driver - version 1.2.0
[    1.993609] Copyright (c) 2013 - 2014 Intel Corporation.
[    1.993684] Intel(R) Ethernet Switch Host Interface Driver - version 0.12.2-k
[    1.993752] Copyright (c) 2013 Intel Corporation.
[    1.993866] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.993934] r8169 0000:03:00.2: can't disable ASPM; OS doesn't have ASPM control
[    1.994679] r8169 0000:03:00.2 eth0: RTL8411 at 0xffffc90000026000, 80:fa:5b:01:6d:12, XID 08800800 IRQ 25
[    1.994762] r8169 0000:03:00.2 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.994856] ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
[    1.994923] ipw2100: Copyright(c) 2003-2006 Intel Corporation
[    1.995001] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kq
[    1.995068] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[    1.995145] libipw: 802.11 data/management/control stack, git-1.1.13
[    1.995212] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[    1.995307] Intel(R) Wireless WiFi driver for Linux
[    1.995372] Copyright(c) 2003- 2014 Intel Corporation
[    1.995584] iwl4965: Intel(R) Wireless WiFi 4965 driver for Linux, in-tree:d
[    1.995652] iwl4965: Copyright(c) 2003-2011 Intel Corporation
[    1.995728] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:ds
[    1.995811] iwl3945: Copyright(c) 2003-2011 Intel Corporation
[    1.995923] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:SYNM] at 0x60,0x64 irq 1,12
[    2.519045] i8042: Detected active multiplexing controller, rev 1.1
[    2.521310] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.521375] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    2.521438] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    2.521501] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    2.521564] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    2.521663] iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-3160-12.ucode failed with error -2
[    2.521699] mousedev: PS/2 mouse device common for all mice
[    2.521801] hidraw: raw HID events driver (C) Jiri Kosina
[    2.521958] iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-3160-11.ucode failed with error -2
[    2.522030] TCP: cubic registered
[    2.522032] NET: Registered protocol family 17
[    2.522068] NET: Registered protocol family 33
[    2.522072] Key type rxrpc registered
[    2.522072] Key type rxrpc_s registered
[    2.522082] lib80211: common routines for IEEE802.11 drivers
[    2.522083] lib80211_crypt: registered algorithm 'NULL'
[    2.522085] lib80211_crypt: registered algorithm 'WEP'
[    2.522087] lib80211_crypt: registered algorithm 'CCMP'
[    2.522088] lib80211_crypt: registered algorithm 'TKIP'
[    2.522099] 9pnet: Installing 9P2000 support
[    2.522451] registered taskstats version 1
[    2.522602] iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-3160-10.ucode failed with error -2
[    2.522689] iwlwifi 0000:04:00.0: request for firmware file 'iwlwifi-3160-10.ucode' failed.
[    2.522769] iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-3160-9.ucode failed with error -2
[    2.522862] iwlwifi 0000:04:00.0: request for firmware file 'iwlwifi-3160-9.ucode' failed.
[    2.522940] iwlwifi 0000:04:00.0: no suitable firmware found!
[    2.523066] Btrfs loaded
[    2.523770] Freeing unused kernel memory: 844K (ffffffff819e4000 - ffffffff81ab7000)
[    2.525038] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    2.589796] libata version 3.00 loaded.
[    2.775569] ahci 0000:00:1f.2: version 3.0
[    2.775688] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    2.775711] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0xf impl SATA mode
[    2.775713] ahci 0000:00:1f.2: flags: 64bit ncq stag led clo pio slum part ems sxs apst 
[    2.930731] scsi host0: ahci
[    2.930824] scsi host1: ahci
[    2.930912] scsi host2: ahci
[    2.930997] scsi host3: ahci
[    2.931082] scsi host4: ahci
[    2.931168] scsi host5: ahci
[    2.931222] ata1: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316100 irq 26
[    2.931224] ata2: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316180 irq 26
[    2.931226] ata3: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316200 irq 26
[    2.931227] ata4: SATA max UDMA/133 abar m2048@0xec316000 port 0xec316280 irq 26
[    2.931228] ata5: DUMMY
[    2.931229] ata6: DUMMY
[    3.010214] tsc: Refined TSC clocksource calibration: 2793.531 MHz
[    3.350586] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    3.351717] ata1.00: ATA-8: HGST HTS721010A9E630, JB0OA3J0, max UDMA/133
[    3.351719] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    3.352951] ata1.00: configured for UDMA/133
[    3.353024] scsi 0:0:0:0: Direct-Access     ATA      HGST HTS721010A9 A3J0 PQ: 0 ANSI: 5
[    3.353163] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    3.353166] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    3.353205] sd 0:0:0:0: [sda] Write Protect is off
[    3.353208] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.353231] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.637281]  sda: sda1 sda2
[    3.637463] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.721050] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.722046] ata2.00: ATA-8: Hitachi HTS545032B9SA02, PB3AC60W, max UDMA/133
[    3.722047] ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    3.723169] ata2.00: configured for UDMA/133
[    3.723224] scsi 1:0:0:0: Direct-Access     ATA      Hitachi HTS54503 C60W PQ: 0 ANSI: 5
[    3.723355] sd 1:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    3.723386] sd 1:0:0:0: [sdb] Write Protect is off
[    3.723388] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    3.723403] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.733717] psmouse serio2: synaptics: queried max coordinates: x [..5662], y [..4660]
[    3.743674]  sdb: sdb1 sdb2
[    3.743859] sd 1:0:0:0: [sdb] Attached SCSI disk
[    3.849335] psmouse serio2: synaptics: queried min coordinates: x [1280..], y [1194..]
[    3.998254] psmouse serio2: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00223/0x840300/0x122c00, board id: 1760, fw id: 1211538
[    4.011423] Switched to clocksource tsc
[    4.035856] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input4
[    4.071462] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    4.075158] ata3.00: ATAPI: TSSTcorp CDDVDW SN-208FB, TC00, max UDMA/100
[    4.078184] ata3.00: configured for UDMA/100
[    4.079606] scsi 2:0:0:0: CD-ROM            TSSTcorp CDDVDW SN-208FB  TC00 PQ: 0 ANSI: 5
[    4.095515] sr 2:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    4.095516] cdrom: Uniform CD-ROM driver Revision: 3.20
[    4.095605] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    4.441900] ata4: SATA link down (SStatus 0 SControl 300)
[    4.512705] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    4.512731] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    4.512754] sr 2:0:0:0: Attached scsi generic sg2 type 5
[    4.597917] scsi: <fdomain> Detection failed (no card)
[    4.713010] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[    4.765628] imm: Version 2.05 (for Linux 2.4.0)
[    4.943498] Fusion MPT base driver 3.04.20
[    4.943499] Copyright (c) 1999-2008 LSI Corporation
[    4.971319] Fusion MPT SPI Host driver 3.04.20
[    4.989095] Fusion MPT FC Host driver 3.04.20
[    5.007323] Fusion MPT SAS Host driver 3.04.20
[    5.021946] 3ware Storage Controller device driver for Linux v1.26.02.003.
[    5.035819] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[    5.050874] HP CISS Driver (v 3.6.26)
[    5.094971] Adaptec aacraid driver 1.2-0[30300]-ms
[    5.127182] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[    5.128035] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    5.158575] megasas: 06.806.08.00-rc1
[    5.175974] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.07.00.16-k.
[    5.205538] Emulex LightPulse Fibre Channel SCSI driver 10.4.8000.0.
[    5.205539] Copyright(c) 2004-2014 Emulex.  All rights reserved.
[    5.244130] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[    6.006264] ACPI: bus type USB registered
[    6.006287] usbcore: registered new interface driver usbfs
[    6.006298] usbcore: registered new interface driver hub
[    6.006319] usbcore: registered new device driver usb
[    6.007782] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.045059] usbcore: registered new interface driver usb-storage
[    6.071657] uhci_hcd: USB Universal Host Controller Interface driver
[    6.096957] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.147599] usbcore: registered new interface driver usbhid
[    6.147600] usbhid: USB HID core driver
[    6.395365] device-mapper: uevent: version 1.0.3
[    6.395408] device-mapper: ioctl: 4.30.0-ioctl (2014-12-22) initialised: dm-devel@redhat.com
[    6.609425] md: raid0 personality registered for level 0
[    6.636061] md: raid1 personality registered for level 1
[    6.670114] async_tx: api initialized (async)
[    6.685225] md: raid6 personality registered for level 6
[    6.685226] md: raid5 personality registered for level 5
[    6.685227] md: raid4 personality registered for level 4
[    6.715091] md: raid10 personality registered for level 10
[    6.742925] md: linear personality registered for level -1
[    6.771441] md: multipath personality registered for level -4
[    6.817020] JFS: nTxBlock = 8192, nTxLock = 65536
[    6.858953] RPC: Registered named UNIX socket transport module.
[    6.858954] RPC: Registered udp transport module.
[    6.858955] RPC: Registered tcp transport module.
[    6.858955] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    6.894536] fuse init (API version 7.23)
[    6.987129] Loading iSCSI transport class v2.0-870.
[    7.237872] UDF-fs: warning (device sdb2): udf_fill_super: No partition found (2)
[    7.244395] (mount,14810,0):ocfs2_fill_super:1026 ERROR: superblock probe failed!
[    7.244396] (mount,14810,0):ocfs2_fill_super:1217 ERROR: status = -22
[    7.244506] gfs2: gfs2 mount does not exist
[    7.244593] BTRFS: device fsid 59b3eb07-79cd-4973-ab94-ae247a4de533 devid 1 transid 2498 /dev/sdb2
[    7.244858] BTRFS info (device sdb2): disk space caching is enabled
[   10.155269] udevd[15044]: starting version 1.5.3
[   10.350015] random: udevd urandom read with 63 bits of entropy available
[   11.104721] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[   11.104759] ACPI: AC Adapter [AC] (on-line)
[   11.105297] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input15
[   11.105330] ACPI: Power Button [PWRB]
[   11.105365] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input16
[   11.105387] ACPI: Sleep Button [SLPB]
[   11.105452] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input17
[   11.105503] ACPI: Lid Switch [LID0]
[   11.105544] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input18
[   11.105566] ACPI: Power Button [PWRF]
[   11.105851] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[   11.105854] ACPI: Battery Slot [BAT0] (battery present)
[   11.242598] ehci-pci: EHCI PCI platform driver
[   11.242711] ehci-pci 0000:00:1a.0: EHCI Host Controller
[   11.242717] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[   11.242727] ehci-pci 0000:00:1a.0: debug port 2
[   11.246616] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[   11.246628] ehci-pci 0000:00:1a.0: irq 16, io mem 0xec318000
[   11.260050] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[   11.260096] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   11.260098] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.260099] usb usb1: Product: EHCI Host Controller
[   11.260100] usb usb1: Manufacturer: Linux 4.0.2-gentoo ehci_hcd
[   11.260101] usb usb1: SerialNumber: 0000:00:1a.0
[   11.260215] hub 1-0:1.0: USB hub found
[   11.260222] hub 1-0:1.0: 2 ports detected
[   11.260405] ehci-pci 0000:00:1d.0: EHCI Host Controller
[   11.260410] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[   11.260420] ehci-pci 0000:00:1d.0: debug port 2
[   11.264306] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[   11.264317] ehci-pci 0000:00:1d.0: irq 23, io mem 0xec317000
[   11.280073] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[   11.280112] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   11.280114] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.280115] usb usb2: Product: EHCI Host Controller
[   11.280117] usb usb2: Manufacturer: Linux 4.0.2-gentoo ehci_hcd
[   11.280117] usb usb2: SerialNumber: 0000:00:1d.0
[   11.280218] hub 2-0:1.0: USB hub found
[   11.280224] hub 2-0:1.0: 2 ports detected
[   11.314427] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   11.314432] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[   11.314498] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[   11.314503] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[   11.314574] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[   11.314576] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.314577] usb usb3: Product: xHCI Host Controller
[   11.314578] usb usb3: Manufacturer: Linux 4.0.2-gentoo xhci-hcd
[   11.314579] usb usb3: SerialNumber: 0000:00:14.0
[   11.314677] hub 3-0:1.0: USB hub found
[   11.314694] hub 3-0:1.0: 14 ports detected
[   11.317356] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   11.317359] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[   11.317406] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[   11.317407] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.317409] usb usb4: Product: xHCI Host Controller
[   11.317410] usb usb4: Manufacturer: Linux 4.0.2-gentoo xhci-hcd
[   11.317410] usb usb4: SerialNumber: 0000:00:14.0
[   11.317512] hub 4-0:1.0: USB hub found
[   11.317524] hub 4-0:1.0: 6 ports detected
[   11.379021] [drm] Initialized drm 1.1.0 20060810
[   11.435122] snd_hda_intel 0000:01:00.1: Disabling MSI
[   11.470198] ACPI Warning: SystemIO range 0x000000000000f000-0x000000000000f01f conflicts with OpRegion 0x000000000000f000-0x000000000000f00f (\_SB_.PCI0.SBUS.SMBI) (20150204/utaddress-258)
[   11.470202] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.471102] thermal LNXTHERM:00: registered as thermal_zone0
[   11.471103] ACPI: Thermal Zone [TZ0] (51 C)
[   11.471104] Monitor-Mwait will be used to enter C-1 state
[   11.471110] Monitor-Mwait will be used to enter C-2 state
[   11.471117] ACPI: acpi_idle registered with cpuidle
[   11.471143] ACPI: Video Device [PEGP] (multi-head: yes  rom: no  post: no)
[   11.580421] usb 1-1: new high-speed USB device number 2 using ehci-pci
[   11.596942] sound hdaudioC0D0: autoconfig for ALC892: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:line
[   11.596944] sound hdaudioC0D0:    speaker_outs=1 (0x14/0x0/0x0/0x0/0x0)
[   11.596945] sound hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   11.596946] sound hdaudioC0D0:    mono: mono_out=0x0
[   11.596947] sound hdaudioC0D0:    dig-out=0x1e/0x0
[   11.596948] sound hdaudioC0D0:    inputs:
[   11.596950] sound hdaudioC0D0:      Mic=0x18
[   11.596951] sound hdaudioC0D0:      Internal Mic=0x12
[   11.596952] sound hdaudioC0D0:      Line=0x1a
[   11.600447] usb 2-1: new high-speed USB device number 2 using ehci-pci
[   11.630483] usb 3-3: new full-speed USB device number 2 using xhci_hcd
[   11.708524] acpi device:02: registered as cooling_device5
[   11.708723] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input19
[   11.730994] usb 1-1: New USB device found, idVendor=8087, idProduct=8008
[   11.730996] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   11.731142] hub 1-1:1.0: USB hub found
[   11.731242] hub 1-1:1.0: 6 ports detected
[   11.751017] usb 2-1: New USB device found, idVendor=8087, idProduct=8000
[   11.751019] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   11.751167] hub 2-1:1.0: USB hub found
[   11.751266] hub 2-1:1.0: 8 ports detected
[   11.772260] usb 3-3: New USB device found, idVendor=1c7a, idProduct=0603
[   11.772262] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   11.772263] usb 3-3: Product: EgisTec_ES603
[   11.772264] usb 3-3: Manufacturer: EgisTec
[   11.779221] input: PC Speaker as /devices/platform/pcspkr/input/input20
[   11.888256] microcode: CPU0 sig=0x306c3, pf=0x10, revision=0x17
[   11.890814] usb 3-7: new full-speed USB device number 3 using xhci_hcd
[   11.911015] microcode: CPU1 sig=0x306c3, pf=0x10, revision=0x17
[   11.911040] microcode: CPU2 sig=0x306c3, pf=0x10, revision=0x17
[   11.911063] microcode: CPU3 sig=0x306c3, pf=0x10, revision=0x17
[   11.911075] microcode: CPU4 sig=0x306c3, pf=0x10, revision=0x17
[   11.911087] microcode: CPU5 sig=0x306c3, pf=0x10, revision=0x17
[   11.911110] microcode: CPU6 sig=0x306c3, pf=0x10, revision=0x17
[   11.911134] microcode: CPU7 sig=0x306c3, pf=0x10, revision=0x17
[   11.911182] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[   12.031918] usb 3-7: New USB device found, idVendor=8087, idProduct=07dc
[   12.031920] usb 3-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   12.050998] sound hdaudioC1D0: autoconfig for ID 40: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[   12.051000] sound hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   12.051002] sound hdaudioC1D0:    hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   12.051003] sound hdaudioC1D0:    mono: mono_out=0x0
[   12.051004] sound hdaudioC1D0:    dig-out=0x5/0x7
[   12.051004] sound hdaudioC1D0:    inputs:
[   12.067768] nvidia: module license 'NVIDIA' taints kernel.
[   12.067769] Disabling lock debugging due to kernel taint
[   12.074530] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   12.074811] [drm] Initialized nvidia-drm 0.0.0 20150116 for 0000:01:00.0 on minor 0
[   12.074817] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  349.16  Wed Apr  8 00:17:22 PDT 2015
[   12.125112] random: nonblocking pool is initialized
[   12.626391] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.626419] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.626435] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.626458] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.626474] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.626500] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.626515] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.626530] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.798215] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   12.798260] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   13.100366] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   15.352382] BTRFS info (device sdb2): disk space caching is enabled
[   15.471318] Adding 4194300k swap on /dev/sda2.  Priority:-1 extents:1 across:4194300k 
[   19.102332] r8169 0000:03:00.2 eth0: link down
[   19.113392] NET: Registered protocol family 10
[   19.113879] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.224518] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.224553] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.224569] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.224593] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.224608] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.224634] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.224650] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.224665] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.287721] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.287760] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   23.338565] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   61.820547] cfg80211: Verifying active interfaces after reg change
[   75.480271] typefind:sink[16784]: segfault at 7f006020be00 ip 00007f006ead8c5f sp 00007f006e0bab60 error 4 in libgsttypefindfunctions.so[7f006eac9000+15000]
[   85.144420] traps: gom-flickr-mine[16942] trap int3 ip:7f87e7db113a sp:7ffe7528bf20 error:0

My thinking is that, since the driver is in /lib/firmware, the system cannot read the ucode (as it tries to load it before the root system is mounted). Is there a way to tell the kernel to look for the driver in the boot partition? If I can put it there, then the driver should load.

allen286 · May 15, 2015

Ok - I have recompiled the kernel with the driver back as a module. I think this is not a firmware problem... Watching the dmesg, it appears to connect, authenticate, and promptly disconnect:

[  123.239152] wlan0: authenticate with 28:cf:da:b0:d2:68
[  123.241905] wlan0: send auth to 28:cf:da:b0:d2:68 (try 1/3)
[  123.243069] wlan0: authenticated
[  123.243523] wlan0: associate with 28:cf:da:b0:d2:68 (try 1/3)
[  123.245457] wlan0: RX AssocResp from 28:cf:da:b0:d2:68 (capab=0x511 status=0 aid=2)
[  123.246390] wlan0: associated
[  123.246434] cfg80211: Calling CRDA for country: US
[  123.246499] wlan0: deauthenticating from 28:cf:da:b0:d2:68 by local choice (Reason: 3=DEAUTH_LEAVING)
[  123.248903] cfg80211: Calling CRDA to update world regulatory domain

Any advice for this one?

overkill · May 15, 2015

Do you have a MAC allow list enabled on the router? Check the log on the router and see what it says. Are you using authentication?

666threesixes666 · May 16, 2015

make sure you're close to the router and get decent signal, remove objects blocking the line of sight path. anything over 50% signal should be good enough.

allen286 · May 16, 2015

I fixed it! The solution was to build NetworkManager 1.0.2 from source. Worked like a charm!

Thank you all for your input, and cheers!

-Hunter a.

666threesixes666 · May 17, 2015

lol portage builds it from source... the question is what use flags did you have to enable?

./configure --help

blah blah blah blah blah

--disable-feature

--disable-nls

--disable-xyz

so networkmanager with all use flags enabled should work from portage.... you and future users with the same hardware don't want that.... figure out the one is absolutely required for your hardware. start with all flags enabled for network manager then start pealing them away 2 by 2 until something breaks. then document the hardware requires the flag in the networkmanager wiki page.

Tassie_Tux · May 18, 2015

I fixed it! The solution was to build NetworkManager 1.0.2 from source. Worked like a charm!

Thank you all for your input, and cheers!

-Hunter a.

Upgrading to NetworkManager 1.0.0 caused my wifi connection to become unusable and dmesg produced a similar output. Eventually I was able to resolve the issue by changing net-misc/networkmanager-1.0.0 USE flags. (Bug report https://bugs.funtoo.org/browse/FL-2372)

Wifi Problems

Question

Link to comment

Share on other sites

15 answers to this question

Recommended Posts

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites

Link to comment

Share on other sites