Jump to content

allen286

Members
  • Content Count

    7
  • Joined

  • Last visited

  1. I fixed it! The solution was to build NetworkManager 1.0.2 from source. Worked like a charm! Thank you all for your input, and cheers! -Hunter a.
  2. Ok - I have recompiled the kernel with the driver back as a module. I think this is not a firmware problem... Watching the dmesg, it appears to connect, authenticate, and promptly disconnect: [ 123.239152] wlan0: authenticate with 28:cf:da:b0:d2:68 [ 123.241905] wlan0: send auth to 28:cf:da:b0:d2:68 (try 1/3) [ 123.243069] wlan0: authenticated [ 123.243523] wlan0: associate with 28:cf:da:b0:d2:68 (try 1/3) [ 123.245457] wlan0: RX AssocResp from 28:cf:da:b0:d2:68 (capab=0x511 status=0 aid=2) [ 123.246390] wlan0: associated [ 123.246434] cfg80211: Calling CRDA for country: US [ 123.246
  3. Unfortunately, I did post the exact message... However, I did figure it out. I managed to get the (*) in the correct spots in genkernel, but the problem has been made worse by this... Now the driver does not load. Here's my new dmesg output: [ 0.000000] Normal [mem 0x0000000100000000-0x000000046effffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff] [ 0.000000] node 0: [mem 0x0000000000100000-0x000000007d21efff] [ 0.000000] node 0: [mem 0x000000007d226000-0x000
  4. So the kernel I'm using has Intel Wireless WiFi MVM Firmware support, but it is compiled as a module. When trying to switch to built in, I get a message that says "This feature depends on another which has been configured as a module. As a result, this feature will be built as a module." Maybe I should use an older version of wpa_supplicant?
  5. I was for some reason unable to directly include the driver... It says that it depends on things being built as modules, so it will be built as a module. Any way to find these dependencies? I think you're on the right track; I never thought to check this.
  6. Thanks for the reply! I did install linux-firmware, and I am using network manager from Gnome 3. Here's lspci -k: 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) Subsystem: CLEVO/KAPOK Computer Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) Kernel driver in use: pcieport 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) Subsystem: CLEVO/KAPOK Computer 8 Series/C220 S
  7. Hey everyone, I am very close on my installation. I built my kernel using genkernel. All the necessary drivers are, as far as I can tell, loading appropriately. I am typing this from my Ubuntu install, however, because I have no internet in Funtoo. The driver modules for both the ethernet and wifi are loading and I am even able to scan for wireless networks; however, I cannot connect to any networks. Any ideas? Let me know if you need any output. thanks in advance! -Hunter A.
×
×
  • Create New...