Jump to content


  • Content Count

  • Joined

  • Last visited

  • Days Won


Everything posted by dhudson

  1. dhudson

    ego trouble

    I think the LANG=C could be a problem, I have this: :~$ locale LANG=en_US.UTF-8 LC_CTYPE="en_US.UTF-8" LC_NUMERIC="en_US.UTF-8" LC_TIME="en_US.UTF-8" LC_COLLATE=POSIX LC_MONETARY="en_US.UTF-8" LC_MESSAGES="en_US.UTF-8" LC_PAPER="en_US.UTF-8" LC_NAME="en_US.UTF-8" LC_ADDRESS="en_US.UTF-8" LC_TELEPHONE="en_US.UTF-8" LC_MEASUREMENT="en_US.UTF-8" LC_IDENTIFICATION="en_US.UTF-8" LC_ALL= and have no problems since my previous post.
  2. the kernel would likely need adjustment also. https://wiki.gentoo.org/wiki/Ryzen
  3. yeah same here same errors, according to bugs.* ego sync will fix but not in my case. mozcoreconf-v5.eclass could not be found by inherit() and also missing automake 1.16
  4. With the latest sync I notice GCC 5.4 is upgrading to 5.4.0-r1. Will this upgrade require a complete rebuild of all packages like going from 5.3 to 5.4? , I am hoping not. I looked at bugs.* to see what this revision is suppose to fix but found not much. thanks
  5. yeah my eyes are bad enough could not handle that. yeah first pic guess didn't pay that close attention. was trying to read the messages about runscript openrc-run.
  6. I did see that but it looks like openrc while loading,.. sorry for my confusion.
  7. well its not clear what your console looks like when you get a prompt.. still white and grey?
  8. is all your services erm.. devices loading? rc-status -a just throwing ideas here.
  9. you might look at openrc seems like it updated lately? my log says dec 27 but I think its updated since then.
  10. xrandr for refresh rate and other useful screen data. of course while X is running,.. your problem looks to be a frame buffer issue. (Arch/Manjaro - OpenRC) ^^^^^^^^^^^^^^^^^^^^^^? something going on here?
  11. I am not sure about that warning, I remember seeing it before but either I maybe deleted it? just checked laptop and there is no warning there either, but can confirm the same problem Maurice reported, putting other hosts in aliases inside the quotes does that but goes away when done the way I described... strange! also @mauricev I don't believe you need to alias your local box like that it already knows its base from the hostname= but I may be wrong.
  12. As I see from your /etc/conf.d/hostname file you are setting aliases from other hosts but my file says: # If your local system has other aliases for your local interfaces, you can # add them here. These will also be added to /etc/hosts for and ::1: # Add aliases for other hosts to /etc/hosts directly. The networking scripts # automatically generate the localhost lines only. #aliases="mybox server1" you should be putting aliases for other hosts in /ect/hosts as the directions say. its how I am doing it and have had no problem like this. may well be why this is occurring.
  13. yes of course assuming dhcpcd is default rc-update add dhcpcd default
  14. just courious , I have static ip set with those files. if you use dhcpcd or other variants you wont need them glad you got it sorted out.
  15. ok so module I guess loaded or you wouldn't get that other info. ls -al /etc/init.d/netif.eth0 cat /etc/conf.d/netif.eth0
  16. 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 68:f7:28:aa:4d:f7 brd ff:ff:ff:ff:ff:ff inet brd scope global dynamic noprefixroute eth0 <<<<<<<< shows you have IP address does it work? ok should of been ' lsmod | grep r8169 ' but ok
  17. thanks , so show output of this ' sudo dmesg | r8169 ' also ' lsmod r8169 ' and ' ip addr '
  18. perhaps firmware is whats needed r8169.c refers to r8168 multiple times... I am no programmer but my r8169 is using r8169 0000:01:00.0: firmware: direct-loading firmware rtl_nic/rtl8168g-2.fw PS also looked I am using 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c) if it matters at all. OP if you could give output of ' sudo lspci -k |grep Ethernet '
  19. yes type "man boot-update" for boot.conf "man boot.conf" or you can look at it here, https://github.com/funtoo/boot-update/blob/master/doc/boot.conf.5.rst suggest you look at /boot directory and find out how kernels are named i.e bzImage or vzImage so you will know what to put in boot.conf.
  20. @aitikin I just made boot usb with system rescue cd, it worked without incident. used the B) option if you are in windows I can not comment I don't use it.
  21. Ah my bad "simple-scan" have you tried: To get a list of devices: scanimage -L To scan with default settings to the file image.pnm: scanimage >image.pnm To print all available options: scanimage -h
  22. your scanner seems to have support but its untested http://www.chiark.greenend.org.uk/doc/libsane/supported.html#Z-CANON try man sane-pixma the sane-devel list is one resource for support.
  23. It is difficult and a lot depends on how you create it and the OS that is creating it on. I went through the process a few years back, but don't remember what worked in the end, sorry I can not be of more help. https://www.funtoo.org/Boot_Methods https://www.funtoo.org/Pure_UEFI_Boot_Guide may or may not help you. I use mbr.
  • Create New...