[addwifi failure]

Thanks so much.  I'll give that a shot tomorrow.  I don't recall selecting anything that should have changed the default behavior.  I was using the desktop flavor.

[addwifi failure]

# nmcli d
DEVICE    TYPE             STATE
wlan0     802-11-wireless  unavailable
eth0      802-3-ethernet   unavailable

Will edit with output of other commands after chrooting from liveUSB to have network connection for copy paste.

 

EDIT TO ADD

That does not seem like it would be helpful after looking at the output it is the info from the liveUSB system that is not relevant.  Will have to type it out by hand.

#ifconfig -a
eth0     Link encap:Ethernet  HWaddr 04:7d:7b:e8:da:0d
         UP BROADCAST MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 frame:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo       Link encap:Local Loopback
         inet addr:127.0.0.1  Mask:255.0.0.0
         inet6 addr: ::1/128 Scope:Host
         UP LOOPBACK RUNNING MTU:65536 Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 frame:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0    Link encap:Ethernet  HWaddr 9c:4e:36:37:37:04
         UP BROADCAST MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 frame:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

# cat /proc/net/wireless

Interface| status | Quality          | Discarded packets          | Missed | WE
         |        | link level noise | nwid crypt frag retry misc | beacon | 22

#cat /proc/net/dev

Interface | Receive                                                 | Transmit
          | bytes packets errs drop fifo frame compressed multicast | bytes packets errs drop fifo colls carrier compressed
eth0:
lo:
wlan0:

There are 0s across the board for all three interfaces.

emerge --info net-misc/networkmanager

Returns too much info.  Will have to output it to a file somehow and pastebin it. EDIT: see attached file.  File did not attach.  Please see http://pastebin.com/hnpudReX for this info.  Thanks.

#ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 brd 127.255.255.255 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2:  eth0: <NO_CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
     link/ether 04:7d:7b:e8:da:0d brd ff:ff:ff:ff:ff:ff
3:  wlan0: <NO_CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
     link/ether 9c:4e:36:37:37:04 brd ff:ff:ff:ff:ff:ff

[addwifi failure]

Thanks. If I wasn't clear I did try the add wifi command after rebooting, not in the chroot. I did build the debian-sources kernel. As far as I know I only have Network Manager in use. Will try nmcli commands and report back. Thanks for your help.

[addwifi failure]

Thanks for the suggestion.  I think the driver is installed and loaded but not sure.

# lsmod | grep wifi
iwlwifi    87837  1  iwldvm
cfg80211   412130  3  iwlwifi,mac80211,iwldvm

I did chroot from a live usb and emerge rfkill.  Now after rebooting and running the addwifi command I get a different error:

Error: Connection activation failed: Device not managed by NetworkManager or unavailable

rfkill list returned two entries, neither of which was soft or hard blocked.

[addwifi failure]

I've been using Linux for years but never a source-based distro.  Going through the installation guide when I got to the step of

# addwifi -S wpa -K 'wifipassword' mywifinetwork

I received an error message as follows:

Traceback (most recent call last):
File "/usr/sbin/addwifi", line 164, in <module>
main()
File "/usr/sbin/addwifi:, line 144 in main
check_call(['rfkill','unblock','wlan','wifi'])
File "/usr/lib64/python3.3/subprocess.py", line 542, in check_call
retcode = call(*popenargs, **kwargs)
File "/usr/lib64/python3.3/subprocess.py", line 523, in call
with Popen(*popenargs, **kwargs) as p:
File "/usr/lib64/python3.3/subprocess.py", line 819, in __init__
restore_signals start_new_session)
File "/usr/lib64/python3.3/subprocess.py", line 1448, in _execute_child
raise child_exception_type(errno_num, err_msg)
FileNotFoundError: [Errno 2] No such file or directory: 'rfkill'

Some googling and forum searches suggested that being in the chroot environment might preclude addwifi from working, however when I boot to the terminal (which goes without error) I get the same error.  I have also confirmed that dbus and the network manager service was running.  Any suggestions on how to further troubleshoot this?  Can't try it right now, because don't have my bootable USB to get into a chroot, but do I need to emerge rfkill?

 

My hardware is a Lenovo U310, Intel C210 series chipset, Core i5 CPU, Network controller is intel centrino wireless-n 2200.  Thanks in advance.

 

EDIT:

Found this.  Not sure what is meant by

 

enable the correct ACPI/WMI driver for your notebook first (CONFIG_HP_WMI?).

but that might be the solution as well.