[Realtek r8168 module install]

48 minutes ago, dhudson said:

just courious , I have static ip set with those files. if you use

dhcpcd or other variants you wont need them

glad you got it sorted out.

Yes, I use dhcpcd as default because I have many problems to connect at my university network.

 

41 minutes ago, Oleg Vinichenko said:

what exact guide used for this configuration?

Funtoo's installation guide

 

.

[Realtek r8168 module install]

2 hours ago, dhudson said:

inet 192.168.1.203/24 brd 192.168.1.255 scope global dynamic noprefixroute eth0 <<<<<<<< shows you have IP address does it work?

Yes, it works... seems to be resolved and the connection is stable.

Funtoo davide # ls -al /etc/init.d/netif.eth0
ls: impossibile accedere a /etc/init.d/netif.eth0: File o directory non esistente

Funtoo davide # cat /etc/conf.d/netif.eth0
cat: /etc/conf.d/netif.eth0: File o directory non esistente

Funtoo davide # lsmod | grep r8169
r8169                  90112  0
mii                    16384  1 r8169

netif.eth0 -> no file or directory(maybe I've missed something during configuration?)

[Realtek r8168 module install]

I've whitelisted r8169 because I need LAN just right now.

So here it's the output with r8169 enabled:

Funtoo davide # lsmod r8169
Usage: lsmod
Funtoo davide # dmesg | grep r8169
[   14.734630] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[   14.734640] r8169 0000:02:00.0: can't disable ASPM; OS doesn't have ASPM control
[   14.744984] r8169 0000:02:00.0 eth0: RTL8168g/8111g at 0xffffa55980cfd000, 68:f7:28:aa:4d:f7, XID 10900800 IRQ 48
[   14.744987] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[   17.037973] r8169 0000:02:00.0: firmware: direct-loading firmware rtl_nic/rtl8168g-3.fw
[   17.054149] r8169 0000:02:00.0 eth0: link down
[   17.054149] r8169 0000:02:00.0 eth0: link down
[   19.864899] r8169 0000:02:00.0 eth0: link up
Funtoo davide # ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 brd 127.255.255.255 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 68:f7:28:aa:4d:f7 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.203/24 brd 192.168.1.255 scope global dynamic noprefixroute eth0
       valid_lft 86134sec preferred_lft 86134sec
    inet6 fe80::bf4f:f610:4421:7a0d/64 scope link noprefixroute
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 92:20:ac:da:61:28 brd ff:ff:ff:ff:ff:ff

 

 

[Realtek r8168 module install]

1 hour ago, dhudson said:

perhaps firmware is whats needed r8169.c refers to r8168 multiple times... I am no programmer but my r8169 is using

r8169 0000:01:00.0: firmware: direct-loading firmware rtl_nic/rtl8168g-2.fw

PS also looked I am using

01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)

if it matters at all.

OP if you could give output of  ' sudo lspci -k |grep Ethernet '

davide@Funtoo ~ $ sudo lspci -k | grep Ethernet

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 10)
    Subsystem: Lenovo RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
    Kernel modules: r8169

 

[Realtek r8168 module install]

Quote

well, this is not entirely 100% true about necessity of disabling module in kernel. Because it can be blacklisted at runtime.  but it's correct that debian-sources has the r8169 enabled as module. This ebuild maybe need correction

As said in the first post the r8169 module has been blacklisted and in the emerge --info that I've posted there isn't a voice about the kernel, that is the debian-sources installed when i put the command emerge -auvDN @world.

[Realtek r8168 module install]

Hi everyone,

I'm new to Funtoo and I have some problems with the install of the module r8168, I also have blacklisted r8169, but the installation continues to fail...

Here is the output of r8168.txt

And the output of emerge --info.txt

Thanks in advance!

emerge_info.txt

r8168.txt